Skip to content
Highest Quality, Hand-Picked Jeep Parts & Accessories Shipped to Your Door
Highest Quality, Hand-Picked Jeep Parts & Accessories Shipped to Your Door
Alpine iLX-F509/ iLX-F511 Head Unit Bundle Installation Guide I '07- '18 Jeep JK Wrangler

Alpine iLX-F509/ iLX-F511 Head Unit Bundle Installation Guide I '07- '18 Jeep JK Wrangler

Please follow these installation tips when you're ready to install your new Alpine iLX-F509 or iLX-F511 into your 2007-2018 Jeep JK.

These tips are intended to be used in conjunction with our full installation video below.  Please read the below guide as any changes to the installation process will be noted in the written guide. 

1. The Body – Consists of the head unit, black dash kit and our custom wiring harness.

  • Make all your vehicle connections as noted in the document below.
  • All the plugs are keyed plugs, which means they only fit their match on the Jeep side. All you’re doing is matching plugs – it may look like a lot of wires but it’s simple.

2007-2017 JK Wiring Diagram


You Will Be Connecting: 

USB Retention Adapter

Navigation Antenna

Alpine Microphone

AM/FM Radio Adapter

OBD2 Plug

Sirius XM Tuner (If Selected)


  • DO NOT POWER ON YOUR HEAD-UNIT BEFORE ALL CONNECTIONS ARE MADE. This will cause an error when the Maestro RR module is trying to initialize to your vehicle.

2. The iLX-509/ F511 Screen – You're going to install this last.

  • Attach/slide the Alpine iLX-F509/ F511 screen into the body.
  • Install 4 stainless screws (2 on each side) to secure the screen to the chassis
  • Install plastic safety/ power clip into top slots
  • Note that the unit will not power if the plastic clip it's installed once the screen is slid into the chassis. 
  • Install plastic cover over the safety/ power clip and screw in with 2 small black screws
  • You have completed installation of your new Alpine Bundle! Congratulations!

Additional Alpine Installation Tips:

  • Sirius XM Tuner - If you selected “Maintain Sirius/XM” at checkout, you’ll receive the SAT1.
    • Maestro SAT1: This will already be attached to your new Sirius/XM tuner. The tuner is located underneath the rear chassis of the Sony radio. 
      • Utilize the factory satellite antenna cable that was plugged in to the back of your factory radio to plug into the provided adapter.
      • You will not use the antenna from the SXV300 (which is located in your spare parts bag) since the SAT1 will maintain your factory satellite antenna.
      • Inside the dash you may find several square plugs of varying colors (i.e. white, gray or black).
        • White/Red – AM/FM Antenna
        • Yellow– Factory Sirius XM AntennaSirius XM Tuner with SAT1
    • If your Jeep did not come with a factory Satellite Radio option, you will need to use the provided Sirius XM antenna cable (located in the spare parts bag).

  • Alpine Microphone - You will need to use the provided Alpine microphone with our bundle. You will need to run the wire and plug into wire labeled “MIC”. We recommend placing it on top of the steering column so it is out of the way and picks up less wind noise.

  • Navigation Antenna - Included in your installation parts bag is a Navigation Antenna. Use the provided antenna to plug into the back of the radio. You may choose to mount the antenna anywhere that it can receive signal. We recommend routing the antenna between the dash and the windshield and mounting on the dash.  As noted in the video, if you notice an issue with the maps identifying the Jeeps precise location, you may need to relocate the antenna to above the soundbar. 

    Navigation Antenna
  • OBD2 Plug - When you receive your bundle the OBD2 plug will be attached to the appropriate connector for reference. The OBD2 plug will need to be connected to the OBD2 port located under the steering wheel. The wire can be routed behind the dash to the back of the radio. The OBD2 is needed to be able to show vehicle diagnostics and real time data in the gauges and vehicle information screens of your new Sony Bundle.
    • The small black plug with the red and yellow braided wire pair needs to be connected to the main wiring harness. 

      OBD2 Plug



First, check the following:
(1) Ensure that all connections are mode between Maestro RR Module and your vehicle connectors.
(2) The Maestro RR may need to be re-flashed with your specific vehicle parameters. To re-flash the module, the module will need to be removed from the vehicle and connected to a computer. Visit idatalink Maestro’s website and click on the green button at the top right of the screen labeled “Flash My Module.”
Next article Alpine iLX-507 Head Unit Bundle Installation Guide I '07- '18 Jeep JK Wrangler

Compare products

{"one"=>"Select 2 or 3 items to compare", "other"=>"{{ count }} of 3 items selected"}

Select first item to compare

Select second item to compare

Select third item to compare