Free US Standard Shipping, 60-Day Returns, 2-Year Warranty
FITS: 2007- 2018 Jeep Wrangler JK

Factory Amplified or Non-Factory Amplified? See "Factory Equipment" tab below for assistance with identifying which package is right for your jeep.

We've taken the guess work out of deciding which equipment is needed for a full sound system for your Jeep JK. Our plug and play bundle is shipped to you fully prepped for an easy installation.

Installation:

• Amp Installation Link - This link demonstrates installing an amp into the Jeep Gladiator which will apply for the Jeep JK in relation to power, ground, new amp location, factory amp bypass harness, RCA's, and speaker wire to the subwoofer.
• Speaker Bundle Installation Link - This video demonstrates both the 07-14 and 15-18 Alpine speaker installation.

TESTED AND APPROVED BY TRAIL SEVEN: Alpine speaker, amp, and sub bundle has been installed and tested on our Trail Seven Jeep and we're pleased to put our stamp of approval on this bundle.

• OVERVIEW
• FACTORY EQUIPMENT
• PRODUCT HIGHLIGHTS
• ASK A QUESTION

• Overview

  Regardless if you have the factory amplified system (Premium), or the factory non-amplified system (Standard), we have a bundle that is right for you and your jeep! You'll find the explanation of factory amplified systems (Premium) and factory non-amplified systems (Standard) on the "Factory Equipment" tab above.

  All of our bundles are pre-wired and completely assembled prior to shipping from our Frederick, Maryland shop. When you get your bundle, it's all prepped and ready for a plug and play install into your Jeep! Here's what you can expect to be in your Kicker mono amp/ sub bundle from Trail Seven.

  • Alpine S2-A55V Amplifier
  • VK6 power kit for a single amp connection- power and ground fully prepped for install with ferrule leads, single fuse block
  • 6-Channel RCA's
  • Speaker wire- fully prepped with ferrules (amp to sub)
  • Alpine speakers based on year chosen
    • 07-14:
      • This package will include (2) 6.5" component mid drivers with a direct fit connection for the knee panels, (2) 1" tweeters for the dash panel tombstone speakers with connectors and crossovers, (2) 6.5" component mid drivers with a direct fit connection to the sound bar with (2) 1" tweeters with mounting brackets for a coaxial connection.
    • 15-18:
      • This package will include (2) 6.5" component mid drivers with a direct fit connection for the knee panels, (2) 1" tweeters with mounting plates, connectors, and crossovers for the dash panel, (2) 6.5" component mid drivers with a direct fit connection to the sound bar, and (2) 1" tweeters with mounting plates to the sound bar.
  • Alpine sub based on selection
    • Single 10” S-Series Shallow Preloaded Subwoofer Enclosure
    • Single 12” S-Series Shallow Preloaded Subwoofer Enclosure
    • Halo S-Series Pre-loaded Sub Enclosure S-DB8V-TRK
  • Follow our installation videos above to complete your speaker upgrade!
  • See below for even more details!

  Interested in our bundle for your JK Jeep but have a question first? Simply complete the form below and we'll get back to you promptly!

  
  

  Ask A Question

• Is your Jeep Factory Amplified?

  Factory Amplified:

  The easiest way to determine if your jeep is factory amplified or not, is to identify the factory subwoofer which is always paired up with the amplified package. See pics for easy identification for the '07- '14 JK and the '15- '18 JK. If your Jeep is equipped with the below, then you will select Factory Amplified from the drop down menu.

  

  
  

  Ask A Question

• Product Highlights

  Our bundle comes to you just as you see it in the product pics which is prepped and ready to install. We terminate the power and ground leads, we set up the amp harness for both factory amplified and non-factory amplified systems. We also pre-terminate the speakers with the appropriate connectors and crossovers so your system bundle is completely ready to install upon receipt.

  Select the correct option for your jeep based on factory amplified or non-factory amplified, then select which subwoofer best fits your application.

  Alpine SPV-65X-WRA Speakers

  The SPV-65X-WRA comes with adapters that allow the speakers to be installed as a component set by mounting the tweeters into the tombstones of older JKs or onto the dash for newer JKs. For older JKs that have a sound bar, the adapters convert the speakers into a coaxial design so they can be installed into the sound bar.

  Driving with the top off is part of the fun of owning a Wrangler, but sometimes you get caught off-guard with the top down and inclement weather. The SPV-65X-WRA is weather resistant and rated IP55, so it’s protected from limited dust ingress and low-pressure water spray from any direction.

  • Built specifically for the 07-18 Jeep Wrangler JK
  • Weather resistant
  • 6.5-inch speakers which can be installed as a component or coaxial system, using the included adapters to fit both the '07-'14 Wranglers as well as the '15-'18 Wranglers
  • CTA-2031 Power Rating: 75W RMS, 225W Peak
  • Nominal impedance 4 Ohm
  • Frequency response 65-22kHz
  • 1” Teteron dome tweeter
  • Steel frame with factory speaker mounting tabs
  • Weather resistant: IP55
  • Includes vehicle specific speaker connectors

  Alpine Next-Gen S-Series 5-Channel Amplifier

  The Next-Gen Alpine S-Series S2-A55V 5-Channel Amplifier is Hi-Res Audio Certified and able to reproduce up to 40kHz frequency response. This ultra-wide bandwidth coupled with the elevated S-Series design brings out a new benchmark for entry-level performance and price.

  • Power Output: 40W x 4 + 200W x 1 @ 4Ω, 60W x 4 + 300W x 1 @ 2Ω
  • Hi-Res Audio Playback (192kHz/24Bit)
    
  • 5-Channel Amplifier
  • High-Efficiency Digital Circuit Design
  • Alpine’s Dual Negative Feedback Control Circuit
  • High Bandwidth Amplifier
  • Alpine’s Premium Class D Circuit Design
  • One-sided terminal layout
  • Top panel sound controls
  • Quick connect power and speaker terminals
  • Optional Remote bass knob compatible (requires RUX-KNOB.2 or RUX-H01, sold separately)
    

  Single 10" S-Series Preloaded Sub Enclosure

  With an ultra-shallow enclosure design and powerful sound output, the 10" S-Series Shallow Preloaded Subwoofer Enclosures give you the best of both worlds in size and sound.

  • Preloaded 10” S-Shallow Subwoofer
  • Dimensions: 18.5” (W) x 4.5” (H) x 12.5” (D)
  • Power Handling: 300W RMS
  • Frequency Response: 35Hz-200Hz
  • X-Max: 11mm 1-Way Linear
  • Nominal Impedance: 2Ω
  • Copper Voice Coil: 2” (50.0mm)
    Single 2 Ohm Voice Coil for a 2 Ohm load (compatible with S2-A55V, KTA-200M, or KTA-30MW Amplifiers)
  • Optimal Sealed Cabinet Quality
  • Neodymium Magnet
  • Front-Mounted Neodymium Motor
  • Alpine Gen2 DD Linear Magnetic Circuit
  • Rugged Polymer Enclosure Cabinet
  • Adjustable, Foam-padded Mounting Brackets for Flexible Installation & Reduced Vibration
    

  Single 12" S-Series Preloaded Sub Enclosure

  With an ultra-shallow enclosure design and powerful sound output, the 12" S-Series Shallow Preloaded Subwoofer Enclosures give you the best of both worlds in size and sound.

  • Dimensions: 22.25” (W) x 5.25” (H) x 13.125” (D)
  • Power Handling: 300W RMS
  • Frequency Response: 30Hz-200Hz
  • X-Max:11mm 1-Way Linear
    
  • Nominal Impedance: 2Ω
  • Copper Voice Coil: 2” (50.0mm)
    Single 2 Ohm Voice Coil for a 2 Ohm load (compatible with S2-A55V, KTA-200M, or KTA-30MW Amplifiers)
  • Optimal Sealed Cabinet Quality
  • Preloaded 12” S-Shallow Subwoofer
  • Neodymium Magnet
  • Front-Mounted Neodymium Motor
  • Alpine Gen2 DD Linear Magnetic Circuit
  • Rugged Polymer Enclosure Cabinet
  • Adjustable, Foam-padded Mounting Brackets for Flexible Installation & Reduced Vibration
    

  Alpine Halo S-Series Preloaded Sub Enclosure S-DB8V-TRK

  With the adjustability from 40" to 51", this subwoofer is a perfect fit for the Jeep Wrangler JK. Two 8” subwoofers are preloaded into a compact enclosure which are a perfect fit for rear cargo area. Rubber “feet” are adjustable in height to accommodate uneven floors and the size does not prevent accessing the cargo area under mat storage bin.

  • 600W RMS
  • Frequency Response: 34Hz-200Hz
  • Dual voice coils wired in parallel for a 2Ω load (Two 4Ω enclosures)
  • Compatible with S2-A60M Amplifier for Optimal Power Output
  • Vented/ Ported Enclosure Tuning Frequency: 36Hz
  • Custom spring-loaded speaker terminals fit up to 12AWG speaker wire
  • 40"-51" (Adjustable Width) x 8-3/4” (H) x 13-3/4” (D)
    
  • Groundbreaking Alpine Halo Design
  • ProLink™ Ported Enclosure
  • Expandable Width from 40" to 51"
    
  • Rubber, Modular Stackable Foot Design Accommodates Uneven Truck Floor Areas
  • Ported Enclosures with Next-Gen R-Series Subwoofers
  • Front Link Alpine Branded Bracket
  • Side-Firing Cabin Loading Ports
  • Premium Alpine Wire Terminals
  • Twist-Lock Grille Mount System
  • CARB Compliant 5/8" MDF Construction
  • Premium Black Carpet
    

  Ask A Question

• Ask A Question