Shop By Vehicle
More Filters
Filter
Audiotec Fischer Plug & Play Full System Installation Guide (Non-B&O System) | '21 - Current Ford Bronco
Welcome to your Helix / MATCH Plug & Play Full System Upgrade for your Non-B&O Bronco!
This page is your home base for the install. It covers the high-level tech tips, your system's wiring schematic, and links to every installation guide for your bundle with a note on what each one covers. Your Helix Compose i3 / MATCH UP 6DSP MK2 (6-Ch / Mono) system is Powered by Audiotec Fischer, Curated by Trail Seven and arrives pre-wired, mounted, and DSP-tuned from our Frederick, MD shop.
If you have any questions, or need anything during the installation, we're only a phone call away. We're available Monday-Friday, 9am-4:30pm est. for any support needed, or you can shoot us an email at support@trailseven.com.
These installation notes are intended to be used in conjunction with your system's wiring schematic (below).
- Disassembly
- Front Speaker Install (Dash & Kick Panels)
- Rear Roll Bar Speaker Pod Install
- Amp Board Install
- Power, Radio T-Harness & Conductor Pro Routing
- Subwoofer Connection - see your enclosure's own guide, listed below
Tech Tips
Tools You Will Need:
• Panel Removal Tool
• 7mm Socket
• 8mm Socket
• 10mm Socket (w/ 6" extension for the Driver side kick panel)
• 13mm Socket
• 10mm Box Wrench (Ratcheting Preferred)
• T-15 Torx (Bass Knob Bracket)
• T-20 Torx
• T-30 Torx (Grab Handles)
• T-50 Torx (2-Door only: seat belt module)
• Phillips Head Drill
• 1/2" Drill Bit (firewall grommet)
• Small Flat Head Screwdriver
• Needle Nose Pliers
• Allen Key Set (5mm for power connections)
• Alcohol & Microfiber Towel
Important Tech Tips/ Recommendations:
- The Conductor Pro must be connected. The system will not broadcast any signal without the Helix Conductor Pro plugged in. If you power up and hear nothing, check this connection first. Walkthrough video: LINK
- Ground wire goes ON TOP of the factory ground. When landing the amp board's ground with the factory 8mm bolt, seat it on top of the factory ground connector. Placing it underneath results in a poor ground, and the amps most likely won't power on.
- Don't connect to the battery until the end. After mounting the fuse bracket, tape the end of the power lead and leave it disconnected until everything else is installed.
- Keep the amp board USB accessible. The USB port on the back of the amp board is your access to the MATCH DSP settings. Your system ships pre-tuned, but leaving this reachable avoids pulling the side panel again if you ever want a live tuning session with us.
- SoundSkins Speaker Kit (SSK-SQSK): Your bundle includes the SoundSkins SSK-SQSK Speaker Kit along with a template for you to cut your own pieces and apply.
- Kick panel sound deadening: Clean the area with alcohol and a microfiber towel first. The outer SoundSkins piece lays over the kick speaker wire, so make sure you have enough wire slack inside the area before applying it.
- Bottom right amp board bolt: Space is tight. Use a 10mm box wrench (ratcheting preferred) for this one.
- Dual 10" Down-Firing option: The two Helix IK W10 SVC2 (2 ohm) subwoofers are wired in parallel with the provided lead (positive to positive, negative to negative), which presents a 1 ohm load to the MATCH UP 1FX.
- Break in: Give the speakers several hours of play time to loosen up from the factory. You'll likely notice an improvement in sound quality after the break-in period.
How Your System Connects (Non-B&O)
Unlike the B&O system, your Non-B&O bundle does not use a PAC module and does not tie into a factory amplifier. Instead, the included Radio T-Harness taps the factory radio's high-level output and feeds it to the MATCH UP 6DSP MK2 high-level inputs. The pre-labeled, plug-and-play Non-B&O amp harness handles the rest - just mate each connector to its matching label, no soldering required:
- Factory front and rear signals feed the MATCH UP 6DSP MK2 high-level inputs.
- The amp harness main run carries the kick speakers (Channels E/F) and the rear pods (Rear Left/Right) directly.
- Two additional Molex-terminated pairs ride in that same main run; the corner dash speakers (Front Left/Right) connect to them via the dash extension leads.
- The 6DSP mono RCA output feeds the MATCH UP 1FX, which powers your subwoofer.
- The Helix Conductor Pro connects to the 6DSP Smart Control Port (SCP).
- Power lands on the Trail Seven Fuse Bracket; grounds land on the included ground distribution block.
The full wiring schematic is being updated and will be posted here shortly.
Your System at a Glance
Helix Compose i3 / MATCH UP 6DSP MK2 Bundle (Non-B&O, 6-Ch / Mono):
- (2) Helix Compose i3 4" Coax Dash Speakers - Ci3 C100.2FM-S3 MK2 (driver and passenger; no center channel)
- (2) Helix Compose i3 6.5" Woofer Kick Panel Speakers - Ci3 W165FM-S3
- (2) Helix Compose i3 6.5" Coax Rear Speakers - Ci3 C165.2FM-S3 (pre-mounted in Trail Seven Rear Pods)
- MATCH UP 6DSP MK2 6-Channel DSP Amplifier + MATCH UP 1FX Mono Amplifier (pre-mounted on the Trail Seven Amp Bracket)
Updated wiring schematic coming shortly.
Your bundle also includes: Helix Conductor Pro bass knob, SoundSkins Speaker Kit (SSK-SQSK) with cutting templates, 1/0 AWG power kit with Trail Seven Fuse Bracket, the Radio T-Harness and Non-B&O amp harness, and your subwoofer choice: Trail Seven 10" Tailgate Enclosure, Trail Seven Dual 10" Down-Firing Sealed Enclosure, SSV Works 10" Side Enclosure (all loaded with the Helix IK W10 SVC2), or the Helix IK ES10.1-DVC2 MK2 down-firing ported enclosure. Broncos without a factory subwoofer also include our Snap-In Shelf Replacement cover for the right rear trim panel.
2-Door Broncos:
- Seat belt module: To seat the amp board, remove the seat belt retraction module (single T-50 Torx bolt underneath). Re-install it once the amp bracket is in place.
- Power & harness routing: 2-Doors don't have the rear trim piece behind the bench. The best route is underneath the rear bench carpet and out to the side. Find your path of least resistance before you start pulling wire.
- The SSV Works 10" Side Enclosure does not fit the 2-Door.
Manual Transmission Broncos:
- The firewall grommet shown in the video is used by the clutch harness on manual Broncos, so power routing will differ. Best practice is either cutting the rubber boot beside the clutch harness and routing through it, routing underneath the Bronco via the drain plug access points, or finding an alternate path you're comfortable with.
Installation Guides & Schematic
1. Amp Wiring Schematic (Non-B&O): COMING SOON
Your complete plug-and-play wiring map - inputs, speaker outputs, the mono amp/subwoofer connection, Conductor Pro, and power/ground. Mate connectors by label; no soldering required.
2. Rear Speaker Pods: LINK
Installing the pre-loaded Trail Seven rear roll-bar pods.
3. Trail Seven Dual 10" Down-Firing Sealed Enclosure (if selected): LINK
Mounting the enclosure's brackets into the factory cargo hook locations, plus the dual subwoofer wiring diagrams.
4. Trail Seven 10" Tailgate Enclosure (if selected): LINK
Removing the tailgate trim, attaching the L brackets, drilling and riveting, and mounting the enclosure. Compatible with Ford's slide-out cargo shelf.
5. SSV Works 10" Side Enclosure (if selected, 4-Door only): LINK
SSV Works' own guide for mounting the enclosure on the Driver side wheel well in the cargo area. The sub wire comes prepped on both ends.
6. Helix IK ES10.1-DVC2 MK2 Down-Firing Ported Enclosure (if selected):
Uses the connector supplied with the Helix enclosure. Attach the bare ends of the sub wire to the connector with a small flat head screwdriver, then plug it into the enclosure.
7. Snap-In Shelf Replacement (Non-B&O, if your Bronco has no factory subwoofer): LINK
Broncos without a factory sub require removing the shelf in the right rear trim panel to fit the amplifier behind it. Our custom-fit, snap-in cover panel finishes it off - included free with your bundle.
Trail Seven Installation Video, Part 1 of 2:
Trail Seven Installation Video, Part 2 of 2: