Skip to content
Black Friday Deals are Live and at the Lowest Prices of the Year! Check out All our Holiday Specials!
Black Friday Deals are Live and at the Lowest Prices of the Year! Check out All our Holiday Specials!

Kenwood Head Unit Bundle Installation Guide (DMX908S, DMX958XR) | '07 - '18 Jeep JK/ JKU Wrangler

Welcome to your Jeep JK Kenwood Head Unit Bundle Installation Guide.

This guide walks you through the entire installation step by step, with the full installation video at the bottom of this page. Every Kenwood radio below uses the same Trail Seven plug and play install in the '07-'18 JK/ JKU Wrangler:

  • Kenwood Excelon DMX908S
  • Kenwood Excelon Reference DMX958XR

Your radio's own Kenwood Instruction Manual and Quick Start Guide are linked in the Kenwood Manuals & Quick Start Guides section below.

If you have any questions, or need anything during the installation, we're only a phone call away. We're available Monday-Friday, 9am-4:30pm EST, or you can email us at support@trailseven.com.

Before you start: make sure the key is OFF. Do not power on your new head unit until all connections are made - powering on early causes an error while the Maestro RR module initializes to your Jeep.


Before starting, please review your products with the list below to make sure you have all needed parts.

What's in your bundle

  • Kenwood head unit, pre-wired with the iDatalink Maestro RR module and JK T-harness - soldered, shrink-wrapped, tesa taped and flashed for your Jeep
  • Metra '07-'18 JK Wrangler dash kit in matte black, pre-installed on the radio
  • OBD2 plug (attached to its connector for reference)
  • USB adapter
  • AM/FM antenna adapter
  • Kenwood microphone and GPS (navigation) antenna
  • SiriusXM SXV300V1 tuner and Metra 40-SIRXM antenna adapter (if selected)
  • Backup camera (if selected): Kenwood CMOS-230LP1 (DMX908S) or Kenwood CMOS-740HDLP1 (DMX958XR), each with the Echomaster PHD-MOUNT spare tire camera mount - or the iBeam backup camera system (DMX908S)

Tools Needed for Install

  • Panel Removal Tool
  • 7mm Socket
  • Zip Ties (for cable management)

Important Tech Tips/ Recommendations

  • Do not power on early - Make every connection before turning the key. Powering on first causes an error while the Maestro RR module initializes.
  • Fully remove the Uconnect module - We suggest removing the Uconnect module, or at least fully disconnecting it. A connected Uconnect can steal part of your phone calls (one-sided calls are the common symptom) and affect Apple CarPlay/ Android Auto.
  • Dash trim fit - In some Jeeps, the plastic trim piece in the dash may need to be shaved down so the head unit slides into place. It varies too much by year and model to predict, and it's rare. A straight blade taking off about 1/16" to 1/8" of the plastic is all that's needed.
  • Keyed plugs - All the plugs only fit their match on the Jeep side. It may look like a lot of wires, but you're simply matching plugs.

2007-2018 JK Wiring Diagram

Installation Steps

  1. Remove the Window Control Module:
    • Use a panel tool to pry the window control module out of the dash panel.
    • Disconnect the connector from the module.
  2. Drop the Panel Underneath the Steering Wheel:
    • Lower the panel to gain access to the dash fasteners.
  3. Remove the Center Dash Bezel:
    • Remove the (x4) 7mm bolts: behind the window module, under the steering wheel, and at the center top of the dash.
    • Pull the dash bezel out - it is held in with clips.
  4. Remove the Factory Radio:
    • Remove the (x4) 7mm bolts holding the factory radio.
    • Disconnect all wires from the back of the radio.
  5. Fully Remove or Disconnect the Uconnect Module:
    • See the tech tip above - a connected Uconnect module can cause one-sided phone calls with CarPlay/Android Auto.
  6. Route the GPS Antenna Wire & Mount the Antenna:
    • Route the wire through the slot near the windshield and pull it out through the head unit cavity.
    • Mount the GPS antenna on top of the dash behind the defrost vents.
    • Zip tie the slack wiring in the cavity.
  7. Route the Microphone:
    • Route the microphone wire through the channel from the head unit cavity.
    • Mount the microphone on top of the steering column.
  8. Route the OBD2 Wire:
    • Run the OBD2 wire from the head unit cavity down to the factory OBD2 port by the left side of the driver's foot well, and plug it in.
  9. Connect Your New Kenwood Head Unit:
    • Plug the pre-wired harness into the Jeep's factory connectors - every plug is keyed, so each one only fits its match.
    • Connect the GPS antenna, microphone, AM/FM antenna adapter and factory AM/FM antenna, amp turn-on, OBD2, and USB.
    • Do not power on the radio until every connection is made.
  10. Connect the Backup Camera (if selected):
    • DMX908S: plug the Kenwood CMOS-230LP1 or iBeam camera into the radio's rear camera input.
    • DMX958XR: plug the Kenwood CMOS-740HDLP1 into the radio's HD rear camera input.
  11. Mount the Kenwood Head Unit:
    • Secure the radio using the (x4) screw slots on the dash kit brackets.
    • Reinstall the dash trim, window control module, and lower panel.
  12. Power Up & Test:
    • Turn the key and confirm the radio powers on, the Maestro module initializes, steering wheel controls work, all speakers play, AM/FM receives, and Apple CarPlay / Android Auto connect.
    • Enjoy your new Kenwood head unit!

Additional Kenwood Installation Tips

  • SiriusXM Tuner - If you selected "Maintain/ Add Sirius XM" at checkout, the SXV300V1 tuner comes connected to your radio with the Metra 40-SIRXM antenna adapter. Plug your Jeep's factory satellite antenna lead (the yellow square plug in the dash) into the 40-SIRXM adapter. If your Jeep did not come with factory satellite radio, use the SiriusXM antenna in your spare parts bag and route it outside the cabin with a clear view of the sky. Inside the dash, the White/ Red square plug is the AM/FM antenna and the Yellow plug is the factory SiriusXM antenna.
  • Kenwood Microphone - Use the provided Kenwood microphone and plug it into the wire labeled "MIC". We recommend the top of the steering column - it's out of the way and picks up less wind noise. The cable is long enough to reach the factory A-pillar mic location if you prefer.
  • GPS (Navigation) Antenna - Plug it into the back of the radio and mount it where it can receive signal. We recommend routing it between the dash and windshield and mounting it on the dash. If your maps don't show the Jeep's precise location, relocate the antenna above the soundbar.
    Navigation Antenna
  • OBD2 Plug - Connect the OBD2 plug to the port under the steering wheel and route the wire behind the dash to the radio. The small black plug with the red and yellow braided pair connects to the main wiring harness. The OBD2 connection shows vehicle diagnostics and real-time data on your Kenwood's vehicle information screens.
    OBD2 Plug
  • Backup Camera - If selected, mount the camera on your spare tire and run the video cable to the radio. The Kenwood CMOS-230LP1 and CMOS-740HDLP1 mount to the spare tire with the included Echomaster PHD-MOUNT adjustable camera mount, which lets you position the camera almost anywhere on the tire for the clearest view. The CMOS-230LP1 (DMX908S) plugs into the radio's rear camera input. For the iBeam camera (DMX908S), also connect the camera's red power lead to the pre-installed red bullet connector on the harness. The Kenwood CMOS-740HDLP1 (DMX958XR) connects to the radio's dedicated HD camera input.

Kenwood Manuals & Quick Start Guides

Kenwood Excelon DMX908S & Excelon Reference DMX958XR

  • Instruction Manual: LINK
  • Quick Start Guide: LINK

Troubleshooting

First, check the following:

  1. Make sure all connections are made between the Maestro RR module and your Jeep's connectors.
  2. The Maestro RR may need to be re-flashed with your Jeep's specific parameters. Remove the module, connect it to a computer, visit iDatalink Maestro's website and click "Flash My Module" at the top right.

Still stuck? Call us Monday-Friday, 9am-4:30pm EST, or email support@trailseven.com.

Trail Seven Installation Video:

Coming soon!

Enjoy your new radio!

Next article

Compare products

{"one"=>"Select 2 or 3 items to compare", "other"=>"{{ count }} of 3 items selected"}

Select first item to compare

Select second item to compare

Select third item to compare

Compare