Shop By Vehicle
More Filters
Filter
Jeep TJ ('97-'06) JVC KW-M695BW Head Unit Install Guide
Welcome to your Jeep TJ JVC KW-M695BW Head Unit Bundle Installation Guide.
This guide walks you through the entire installation step by step. The '97-'02 and '03-'06 TJ use different dash kits and harnesses, so jump to the section for your year:
If you have any questions, or need anything during the installation, we're only a phone call away. We're available Monday-Friday, 9am-5pm EST, or you can email us at support@trailseven.com.
IMPORTANT NOTICE FOR TJ OWNERS:
Due to the unique nature of the TJ model, even from the factory, there may be wiring, plugs, or components that differ from the original specifications. Modifications may also have been made by previous owners. While our audio systems are designed to be plug-and-play, these variations can sometimes affect compatibility. We strongly recommend inspecting your vehicle's existing audio system before installing. Any adjustments or modifications required beyond this guide are the responsibility of the customer.
Before you start: make sure the key is OFF. Do not remove the factory radio with the key on or the engine running.
Trail Seven's Installation Video: Coming soon!
1997 - 2002 TJ Wrangler
Before starting, please review your products with the list below to make sure you have all needed parts.
What's in your bundle
- JVC KW-M695BW with the Metra 70-1817 TJ wiring harness (2 connectors) already soldered, shrink-wrapped and tesa taped, with quick-disconnect speaker (Molex) and amp turn-on (pink bullet) connections
- Metra 95-6549 '97-'02 TJ double-DIN dash kit - side brackets and top storage tray pre-installed on the radio
- AM/FM antenna adapter
- Installation bag: JVC microphone, Metra kit manual, Metra kit pieces (tray and a blank)
- Small parts bag: climate control panel spacers (for '97-'99 Jeeps) and extra screws
Tools Needed for Install
- Panel Removal Tool
- 7mm Socket OR Phillips Screwdriver
- 10mm Socket
- Shears (or preferred cutting tool)
- Drill with a small bit
- Zip Ties (for cable management)
Installation Steps - '97-'02
-
Dash Disassembly:
- Remove top dash trim and screws.
- Remove tray, then the screw behind it.
- Set the dash piece aside (you'll need the air vents for the new kit).
-
Remove Factory Radio:
- Unscrew (x2) 10mm bolts.
- Disconnect all OEM connections from the radio, including the antenna.
-
Remove Temperature Control Panel:
- Unscrew (x4) Phillips head screws.
- Disconnect all connectors from the control panel.
-
Remove Plastic Trim in Dash Cavity:
- Use a cutting tool to trim the piece for the new head unit.
-
Run Wires (Mic, USB):
- Position wires where preferred (see tips at the bottom of this guide).
-
Drill Holes for New Head Unit Brackets:
- Align the new unit and drill small starter holes.
-
Connect Wires to New Head Unit:
- Plug both connectors of the pre-soldered Metra harness into the Jeep's factory radio connectors.
- Connect the AM/FM antenna adapter between the Jeep antenna lead and the radio.
- Connect USB, microphone, and RCAs (if adding an amplifier).
-
Mount New Head Unit:
- Use the provided and factory hardware.
-
Mount Ground Wire to Bolt:
- Attach the ring-terminal ground wire behind the unit using a 10mm bolt.
-
Install Spacers & Mount Temperature Control Panel:
- '97-'99 owners: use the included spacers for proper fit.
-
Install Clips & Tray on New Trim:
- Transfer clips from the factory trim and install the top tray.
-
Install Trim into Jeep:
- Make sure the USB cable is routed before mounting the trim.
- Attach trim with factory screws.
-
Attach Tray to Trim:
- Secure the tray to the trim with screws.
-
Power Up & Test:
- Turn the key and confirm the radio powers on, all speakers play, AM/FM receives, and Apple CarPlay / Android Auto connect.
Jump to 2003 - 2006 | Jump to Installation Tips
2003 - 2006 TJ Wrangler
Before starting, please review your products with the list below to make sure you have all needed parts.
What's in your bundle
- JVC KW-M695BW with the Metra 70-6502 TJ wiring harness (1 connector) already soldered, shrink-wrapped and tesa taped, with quick-disconnect speaker (Molex) and amp turn-on (pink bullet) connections
- Metra 95-6541 '03-'06 TJ radio/climate control panel - side brackets and trim panel pre-installed, lower dash pieces pre-trimmed for fit
- Installation bag: JVC microphone, AM/FM antenna adapter, Metra kit manual
Tools Needed for Install
- Panel Removal Tool
- Phillips Screwdriver
- 10mm Socket
- Cutting tool (for the sub-dash)
- Zip Ties (for cable management)
Installation Steps - '03-'06
-
Remove Defroster Grille:
- Unsnap and remove the defroster grille at the top of the dash.
- Remove the (x2) Phillips screws underneath.
-
Remove Radio/Climate Control Bezel:
- Unsnap the factory radio/climate control panel and set it aside - you'll reuse its A/C vents and clips.
-
Remove Factory Radio:
- Remove the glove box door for access, then remove the (x1) 10mm nut securing the rear of the radio.
- Remove the (x4) Phillips screws securing the radio.
- Disconnect all OEM connections, including the antenna, and remove the radio.
-
Move Climate Control Panel Aside:
- Remove the (x4) Phillips screws securing the climate control panel and move it out of the way.
-
Trim the Sub-Dash:
- Cut and remove the section of the sub-dash behind the radio opening to make room for the new head unit (see the Metra kit manual for the exact area).
-
Reinstall Climate Control Panel:
- Secure it back in place with the factory screws.
-
Transfer Vents & Clips to the New Panel:
- Unclip the A/C vents and the (x4) panel clips from the factory bezel and install them on the new Metra radio/climate control panel.
-
Run Wires (Mic, USB):
- Position wires where preferred (see tips below).
-
Connect Wires to New Head Unit:
- Plug the pre-soldered Metra harness into the Jeep's factory radio connector.
- Connect the AM/FM antenna adapter between the Jeep antenna lead and the radio.
- Connect USB, microphone, and RCAs (if adding an amplifier).
-
Test Before Final Install:
- Turn the key and confirm the radio powers on, all speakers play, AM/FM receives, and Apple CarPlay / Android Auto connect. Turn the key off again before continuing.
-
Mount New Head Unit:
- Secure the radio assembly into the dash using the factory screws and rear 10mm nut.
-
Reassemble the Dash:
- Install the new Metra radio/climate control panel, then reinstall the defroster grille screws and grille, and the glove box door.
Additional JVC Installation Tips (all years)
- Quick-Disconnect Connections - The two white Molex connectors (speakers) and the pink bullet connector (amp turn-on) on the harness come plugged together. Leave them connected - this keeps your factory speakers and factory subwoofer working. They are only unplugged if you add a Trail Seven amplifier package later.
- JVC Microphone - Use the provided JVC microphone with our bundle. Run the wire and plug it into the microphone input on the back of the radio. We recommend placing it on top of the steering column so it is out of the way and picks up less wind noise.
- USB - The KW-M695BW's USB input is on the back of the radio. Route the USB cable to where you want it (glove box, center console, or under the dash) before mounting the trim.
- Firmware - Check for the latest JVC firmware before or after your install: AV Receiver Updates
JVC KW-M695BW Installation Manual & Quick Start Guide
- JVC KW-M695BW Instruction Manual: Download PDF
- JVC KW-M695BW Quick Start Guide: Download PDF
Still need a hand? We're available Monday-Friday, 9am-5pm EST, or email support@trailseven.com.